New Jersey Driving Test Parallel Parking Dimensions

| 25-03-2021
[RAND-1-100] Comments

​

So, when taking the CDL skills test, how do you know the layout of the course? That is exactly what we are going to cover in this article.

The parallel parking space used during the road test is approximately 25 feet long. The larger the family vehicle is, the more problematic it may be for your teen to successfully parallel park such a vehicle. Our Honda Civics fit very comfortably into the parking space at MVC. Few driving tasks are as intimidating as parallel parking.

Parallel parking of a car in NJ for Drivers Road Test. Parallel parking of a car in NJ for Drivers Road Test. Parallel parking. Yielding to right-of-way What to bring to a road test. The ( 6 Points of ID) you used to obtain a permit. An accompanying New Jersey licensed driver who is at least age 21 and has had their New Jersey driver’s license for at least three years. The standard parallel parking dimensions utilized in the driver's license test are 22 feet in length by 10 feet in depth. New Jersey residents taking their driving test can now use backup cameras, as well as parking sensors, thanks to a bill signed into law on Sept. 6, 2016, by Gov. Chris Christie. Best Answer: The road test allows the driver to demonstrate an understanding of safe driving by adhering to the rules of the road.

The CDL skills test consists of the following:

  • Straight Line Backing
  • Offset backing either Left or Right
  • Parallel Parking either Drivers side or Conventional
  • Alley Dock or 90 degree backing

​

New Jersey Driving Test Parallel Parking Dimensions Youtube Video

You may not be tested on all these maneuvers, but instead you may be tested on just a few. In addition, Pre-Trip Inspections are also tested. Look for that article to come out soon.

We do have an in depth article on the CDL skills backing tests, with video explanations. To access that page go here

What follows is a layout of the cones and a description taken directly from one State’s CDL handbook. As always download a copy and compare to ensure you are following your State’s testing protocol. Most of the State’s do now have it pretty standardized so it shouldn’t vary greatly.

If you need to obtain a copy of your State CDL handbook we have you covered. Go here to obtain your FREE instantly downloadable copy.

CDL Straight Line Backing – Cone Dimensions

New Jersey Driving Test Sample

Official guidance from the CDL manual:

You may be asked to back your vehicle in a straight line between two rows of cones without touching or crossing over the exercise boundaries.

So the dimensions of this course are 100 feet long by 12 feet wide.

​

CDL Offset Backing – Cone Dimensions

From the CDL manual:

Offset Back Right – You may be asked to back into a space that is to the right rear of your vehicle. You will drive straight forward the outer boundary. From that position, you must back the vehicle into the opposite lane until the front of your vehicle has passed the first set of cones without striking boundary lines or cones.

Offset Back Left – You may be asked to back into a space that is to the left rear of your vehicle. You will drive straight forward the outer boundary. From that position, you must back the vehicle into the opposite lane until the front of your vehicle has passed the first set of cones without striking boundary lines or cones

Depending on the Class of CDL license you are testing for:

The length of the forward boundary for a Class A license is 140 feet from the rear set of cones. For a Class B license it is 90 feet.

In addition, the two lanes are 12 foot wide, with the lane being backed into 40 feet deep.

​

CDL Parallel Parking Dimensions

The CDL Manual advises:

Parallel Park (Driver’s Side) - You may be asked to park in a parallel parking space that is on your left. You are to drive past the entrance to the parallel parking space with your vehicle parallel to the parking area; and back into the space without crossing front, side or rear boundaries marked by cones. You are required to get your entire vehicle completely into the space.

DrivingDriving

Parallel Park (Conventional) - You may be asked to park in a parallel parking space that is on your right. You are to drive past the entrance to the parallel parking space with your vehicle parallel to the parking area; and back into the space without crossing front, side or rear boundaries marked by cones. You are required to get your entire vehicle completely into the space.

As you can see the dimensions of the box required to put the vehicle into are 12 foot wide by a length that is 15 feet longer than the vehicle (Applies to Class A and Class B).

​

CDL Alley Dock

Guidance from the CDL manual:

You may be asked to sight-side back your vehicle into an alley. You will drive past the alley and position your vehicle parallel to the outer boundary. From that position, back into the alley bringing the rear of your vehicle within three feet of the rear of the alley without touching boundary lines or cones. Your vehicle must be straight within the alley/lane when completed.

The ‘Dock’ space where you will end up is measured as 12 foot wide by 40 foot long. There is an additional spacing of 70 feet forward of this boundary to the outer boundary.

​

Summary

Knowing the placement of the cones will assist you in getting comfortable with the tasks required to complete your CDL skills testing. Don’t forget that we offer a further in depth article with videos that you can check out.

Pa Drivers Test Parallel Parking

​Want the best resource to pass your CDL exam? Go here:

Also don’t forget to be sure to pick up our FREE guides on:

Michigan Parallel Parking Test Dimensions

6 Hacks for boosting pay as a new Truck Driver

Free New Jersey Driving Test

Avoiding the 11 biggest mistakes before starting CDL School

Parallel Parking Test Dimensions Ohio

Nj dmv parallel parking distance

New Jersey Driving Test Manual

And our Cheat sheet checklist of what to ask trucking company recruiters